High passing rate of Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) 100-105
With IT get good at team, each of our all analyze practice stuff are over with high quality. Each of our 100-105 specific tests are prepared for IT examinees, including scholars, certified excel at, IT task persons and even more. It’s for people who need to pass typically the 100-105 audit in a short time using short-term analyze on it. A lot of the candidates decide on our Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) investigation materials to 100-105 exclusively for one time. Typically the practice testing provide by simply us have many exact questions along with answers, soon after 20-30 hours’ study upon it, you are sure to go it. And the most people have transferred their assessments with high 98%-100% passing fee training on the web.
1. What is the default maximum number of equal-cost paths that can be placed into the routing table of a
Cisco OSPF router?
To control the maximum number of parallel routes that Open Shortest Path First (OSPF)
can support, use the maximum-paths command.
Maximum number of parallel routes that OSPF can install in a routing table. The range is from 1 to 16 routes.
Command Default 8 paths
2. Which command can you use to manually assign a static IPV6 address to a router interface?
A. ipv6 address PREFIX_1::1/64
B. ipv6 autoconfig 2001:db8:2222:7272::72/64
C. ipv6 autoconfig
D. ipv6 address 2001:db8:2222:7272::72/64
An example of configuring IPv6 on an interface is shown below: Router(config)# interface fastethernet 0/1
Router(config-if)# ipv6 address 3000::2222:1/64
3. ROUTER# show ip route
192.168.12.0/24 is variably subnetted, 9 subnets, 3 masks C 192.168.12.64 /28 is directly connected,
Loopback1 C 192.168.12.32 /28 is directly connected, Ethernet0 C 192.168.12.48 /28 is directly connected,
Loopback0 O 192.168.12.236 /30 [110/128] via 192.168.12.233, 00:35:36, Serial0 C 192.168.12.232 /30 is
directly connected, Serial0 O 192.168.12.245 /30 [110/782] via 192.168.12.233, 00:35:36, Serial0 O
192.168.12.240 /30 [110/128] via 192.168.12.233, 00:35:36, Serial0 O 192.168.12.253 /30 [110/782] via
192.168.12.233, 00:35:37, Serial0 O 192.168.12.249 /30 [110/782] via 192.168.12.233, 00:35:37, Serial0 O
192.168.12.240/30 [110/128] via 192.168.12.233, 00:35:36, Serial 0
To what does the 128 refer to in the router output above?
A. OSPF cost
B. OSPF priority
C. OSPF hop count
D. OSPF ID number
E. OSPF administrative distance
The first parameter is the Administrative Distance of OSPF (110) while the second parameter is the cost of OSPF.
4. Which two of these statements are true of IPv6 address representation? (Choose two.)
A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B. A single interface may be assigned multiple IPv6 addresses of any type.
C. Every IPv6 interface contains at least one loopback address.
D. The first 64 bits represent the dynamically created interface ID.
E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.
A single interface may be assigned multiple addresses of any type (unicast, anycast, multicast).
Every IPv6-enabled interface must contain at least one loopback and one link-local address.
Optionally, every interface can have multiple unique local and global addresses.
IPv6 host addresses can be assigned in multiple ways:
When IPv6 is used over Ethernet networks, the Ethernet MAC address can be used to generate the 64-bit
interface ID for the host. This is called the EUI-64 address.
Since MAC addresses use 48 bits, additional bits must be inserted to fill the 64 bits required.